ArduinoStuff - arduino stuffs


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181

# Servo library

## Methods

### `attach()`

Attach the Servo variable to a pin. Note that in Arduino 0016 and earlier, the Servo library supports servos on only two pins: 9 and 10.

#### Syntax

```
servo.attach(pin) 
servo.attach(pin, min, max)
```

#### Parameters

* _servo_: a variable of type `Servo`
* _pin_: the number of the pin that the servo is attached to
* _min_ (optional): the pulse width, in microseconds, corresponding to the minimum (0 degree) angle on the servo (defaults to 544)
* _max_ (optional): the pulse width, in microseconds, corresponding to the maximum (180 degree) angle on the servo (defaults to 2400)

#### Example

```
#include <Servo.h> 

Servo myservo;

void setup() 
{ 
  myservo.attach(9);
} 

void loop() {} 
```

#### See also

* [attached()](#attached)
* [detach()](#detach)

### `write()`

Writes a value to the servo, controlling the shaft accordingly. On a standard servo, this will set the angle of the shaft (in degrees), moving the shaft to that orientation. On a continuous rotation servo, this will set the speed of the servo (with 0 being full-speed in one direction, 180 being full speed in the other, and a value near 90 being no movement).

#### Syntax

```
servo.write(angle)
```

#### Parameters

* _servo_: a variable of type Servo
* _angle_: the value to write to the servo, from 0 to 180

#### Example

````
#include <Servo.h> 

Servo myservo;

void setup() 
{ 
  myservo.attach(9);
  myservo.write(90);  // set servo to mid-point
} 

void loop() {} 
````
#### See also

* [attach()](#attach)
* [read()](#read)

### `writeMicroseconds()`

Writes a value in microseconds (us) to the servo, controlling the shaft accordingly. On a standard servo, this will set the angle of the shaft. On standard servos a parameter value of 1000 is fully counter-clockwise, 2000 is fully clockwise, and 1500 is in the middle.

Note that some manufactures do not follow this standard very closely so that servos often respond to values between 700 and 2300. Feel free to increase these endpoints until the servo no longer continues to increase its range. Note however that attempting to drive a servo past its endpoints (often indicated by a growling sound) is a high-current state, and should be avoided.

Continuous-rotation servos will respond to the writeMicrosecond function in an analogous manner to the write function.

#### Syntax

````
servo.writeMicroseconds(us)
````

#### Parameters

* _servo_: a variable of type Servo
* _us_: the value of the parameter in microseconds (int)

#### Example

````
#include <Servo.h> 

Servo myservo;

void setup() 
{ 
  myservo.attach(9);
  myservo.writeMicroseconds(1500);  // set servo to mid-point
} 

void loop() {} 
````

#### See also

* [attach()](#attach)
* [read()](#read)


### `read()`

Read the current angle of the servo (the value passed to the last call to [write()](#write)).

#### Syntax

````
servo.read()
````

#### Parameters

* _servo_: a variable of type `Servo`

#### Returns

The angle of the servo, from 0 to 180 degrees.

#### See also

* [write()](#write)

### `attached()`

Check whether the Servo variable is attached to a pin.

#### Syntax

```
servo.attached()
```

#### Parameters

* _servo_: a variable of type `Servo`

#### Returns

`true` if the servo is attached to pin; `false` otherwise.

#### See also

* [attach()](#attach)
* [detach()](#detach)

### `detach()`

Detach the Servo variable from its pin. If all Servo variables are detached, then pins 9 and 10 can be used for PWM output with [analogWrite()](https://www.arduino.cc/reference/en/language/functions/analog-io/analogwrite/).

#### Syntax

```
servo.detach()
```

#### Parameters

* _servo_: a variable of type `Servo`

#### See also

* [attach()](#attach)
* [attached()](#attached)