bendns' repos / ArduinoStuff
arduino stuffs
Diffstat (limited to 'libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino')
-rw-r--r--libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino130
1 files changed, 0 insertions, 130 deletions
diff --git a/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino b/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino
deleted file mode 100644
index 6607f43..0000000
--- a/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino
+++ /dev/null
@@ -1,130 +0,0 @@
-/*
- Repeating Web client
-
- This sketch connects to a a web server and makes a request
- using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or
- the Adafruit Ethernet shield, either one will work, as long as it's got
- a Wiznet Ethernet module on board.
-
- This example uses DNS, by assigning the Ethernet client with a MAC address,
- IP address, and DNS address.
-
- Circuit:
- * Ethernet shield attached to pins 10, 11, 12, 13
-
- created 19 Apr 2012
- by Tom Igoe
- modified 21 Jan 2014
- by Federico Vanzati
-
- http://www.arduino.cc/en/Tutorial/WebClientRepeating
- This code is in the public domain.
-
- */
-
-#include <SPI.h>
-#include <Ethernet.h>
-
-// assign a MAC address for the ethernet controller.
-// fill in your address here:
-byte mac[] = {
- 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
-};
-// Set the static IP address to use if the DHCP fails to assign
-IPAddress ip(192, 168, 0, 177);
-IPAddress myDns(192, 168, 0, 1);
-
-// initialize the library instance:
-EthernetClient client;
-
-char server[] = "www.arduino.cc"; // also change the Host line in httpRequest()
-//IPAddress server(64,131,82,241);
-
-unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds
-const unsigned long postingInterval = 10*1000; // delay between updates, in milliseconds
-
-void setup() {
- // You can use Ethernet.init(pin) to configure the CS pin
- //Ethernet.init(10); // Most Arduino shields
- //Ethernet.init(5); // MKR ETH shield
- //Ethernet.init(0); // Teensy 2.0
- //Ethernet.init(20); // Teensy++ 2.0
- //Ethernet.init(15); // ESP8266 with Adafruit Featherwing Ethernet
- //Ethernet.init(33); // ESP32 with Adafruit Featherwing Ethernet
-
- // start serial port:
- Serial.begin(9600);
- while (!Serial) {
- ; // wait for serial port to connect. Needed for native USB port only
- }
-
- // start the Ethernet connection:
- Serial.println("Initialize Ethernet with DHCP:");
- if (Ethernet.begin(mac) == 0) {
- Serial.println("Failed to configure Ethernet using DHCP");
- // Check for Ethernet hardware present
- if (Ethernet.hardwareStatus() == EthernetNoHardware) {
- Serial.println("Ethernet shield was not found. Sorry, can't run without hardware. :(");
- while (true) {
- delay(1); // do nothing, no point running without Ethernet hardware
- }
- }
- if (Ethernet.linkStatus() == LinkOFF) {
- Serial.println("Ethernet cable is not connected.");
- }
- // try to congifure using IP address instead of DHCP:
- Ethernet.begin(mac, ip, myDns);
- Serial.print("My IP address: ");
- Serial.println(Ethernet.localIP());
- } else {
- Serial.print(" DHCP assigned IP ");
- Serial.println(Ethernet.localIP());
- }
- // give the Ethernet shield a second to initialize:
- delay(1000);
-}
-
-void loop() {
- // if there's incoming data from the net connection.
- // send it out the serial port. This is for debugging
- // purposes only:
- if (client.available()) {
- char c = client.read();
- Serial.write(c);
- }
-
- // if ten seconds have passed since your last connection,
- // then connect again and send data:
- if (millis() - lastConnectionTime > postingInterval) {
- httpRequest();
- }
-
-}
-
-// this method makes a HTTP connection to the server:
-void httpRequest() {
- // close any connection before send a new request.
- // This will free the socket on the WiFi shield
- client.stop();
-
- // if there's a successful connection:
- if (client.connect(server, 80)) {
- Serial.println("connecting...");
- // send the HTTP GET request:
- client.println("GET /latest.txt HTTP/1.1");
- client.println("Host: www.arduino.cc");
- client.println("User-Agent: arduino-ethernet");
- client.println("Connection: close");
- client.println();
-
- // note the time that the connection was made:
- lastConnectionTime = millis();
- } else {
- // if you couldn't make a connection:
- Serial.println("connection failed");
- }
-}
-
-
-
-