arduino stuffs
Diffstat (limited to 'libraries/Firmata/examples/StandardFirmataBLE/bleConfig.h')
| -rw-r--r-- | libraries/Firmata/examples/StandardFirmataBLE/bleConfig.h | 168 |
1 files changed, 0 insertions, 168 deletions
diff --git a/libraries/Firmata/examples/StandardFirmataBLE/bleConfig.h b/libraries/Firmata/examples/StandardFirmataBLE/bleConfig.h deleted file mode 100644 index 412bb84..0000000 --- a/libraries/Firmata/examples/StandardFirmataBLE/bleConfig.h +++ /dev/null @@ -1,168 +0,0 @@ -/*================================================================================================== - * BLE CONFIGURATION - * - * If you are using an Arduino 101, you do not need to make any changes to this file (unless you - * need a unique ble local name (see below). If you are using another supported BLE board or shield, - * follow the instructions for the specific board or shield below. - * - * Make sure you have the Intel Curie Boards package v2.0.2 or higher installed via the Arduino - * Boards Manager. - * - * Supported boards and shields: - * - Arduino 101 (recommended) - * - RedBearLab BLE Shield (v2) ** to be verified ** - * - RedBearLab BLE Nano ** works with modifications ** - * - Adafruit Feather M0 Bluefruit LE - * - *================================================================================================*/ - -// change this to a unique name per board if running StandardFirmataBLE on multiple boards -// within the same physical space -#define FIRMATA_BLE_LOCAL_NAME "FIRMATA" - -/* - * Arduino 101 - * - * Make sure you have the Intel Curie Boards package v2.0.2 or higher installed via the Arduino - * Boards Manager. - * - * Test script: https://gist.github.com/soundanalogous/927360b797574ed50e27 - */ -#ifdef _VARIANT_ARDUINO_101_X_ -// After conversion to units of 1.25ms, both values must be between -// 0x0006 (7.5ms) and 0x0c80 (4s) -#define FIRMATA_BLE_MIN_INTERVAL 8 // ( 8 * 1000) / 1250 == 0x06 -> 7.5ms -#define FIRMATA_BLE_MAX_INTERVAL 30 // (30 * 1000) / 1250 == 0x18 -> 30ms -#endif - - -/* - * RedBearLab BLE Shield - * - * If you are using a RedBearLab BLE shield, uncomment the define below. - * Also, change the define for BLE_RST if you have the jumper set to pin 7 rather than pin 4. - * - * You will need to use the shield with an Arduino Zero, Due, Mega, or other board with sufficient - * Flash and RAM. Arduino Uno, Leonardo and other ATmega328p and Atmega32u4 boards to not have - * enough memory to run StandardFirmataBLE. - * - * TODO: verify if this works and with which boards it works. - * - * Test script: https://gist.github.com/soundanalogous/927360b797574ed50e27 - */ -//#define REDBEAR_BLE_SHIELD - -#ifdef REDBEAR_BLE_SHIELD -#define BLE_REQ 9 -#define BLE_RDY 8 -#define BLE_RST 4 // 4 or 7 via jumper on shield -#endif - - -/* - * Adafruit Feather M0 Bluefruit LE - * - * If you are using an Adafruit Feather M0 Bluefruit LE, uncomment the define below. - * This configuration should also work with other Bluefruit LE boards/modules that communicate - * with the nRF51822 via SPI (e.g. Bluefruit LE SPI Friend, Bluefruit LE Shield), although - * you may need to change the values of BLE_SPI_CS, BLE_SPI_IRQ, and/or BLE_SPI_RST below. - * - * You will need to install a lightly-modified version of the Adafruit BluefruitLE nRF51 - * package, available at: - * https://github.com/cstawarz/Adafruit_BluefruitLE_nRF51/archive/firmata_fixes.zip - */ -//#define BLUEFRUIT_LE_SPI - -#ifdef BLUEFRUIT_LE_SPI -// Both values must be between 10ms and 4s -#define FIRMATA_BLE_MIN_INTERVAL 10 // 10ms -#define FIRMATA_BLE_MAX_INTERVAL 20 // 20ms - -#define BLE_SPI_CS 8 -#define BLE_SPI_IRQ 7 -#define BLE_SPI_RST 4 -#endif - - -/* - * Generic settings - */ -#if !defined(FIRMATA_BLE_MIN_INTERVAL) && !defined(FIRMATA_BLE_MAX_INTERVAL) -// These values apply to all devices using the Arduino BLEPeripheral library -// with a Nordic nRF8001 or nRF51822. Both values must be between -// 0x0006 (7.5ms) and 0x0c80 (4s). -#define FIRMATA_BLE_MIN_INTERVAL 0x0006 // 7.5ms (7.5 / 1.25) -#define FIRMATA_BLE_MAX_INTERVAL 0x0018 // 30ms (30 / 1.25) -#endif - -#if !defined(FIRMATA_BLE_TXBUFFER_FLUSH_INTERVAL) -#define FIRMATA_BLE_TXBUFFER_FLUSH_INTERVAL 30 // 30ms -#endif - - -/*================================================================================================== - * END BLE CONFIGURATION - you should not need to change anything below this line - *================================================================================================*/ - -#ifdef _VARIANT_ARDUINO_101_X_ -#include "utility/BLEStream.h" -BLEStream stream; -#endif - - -#ifdef REDBEAR_BLE_SHIELD -#include <SPI.h> -#include "utility/BLEStream.h" -BLEStream stream(BLE_REQ, BLE_RDY, BLE_RST); -#endif - - -#ifdef BLUEFRUIT_LE_SPI -#include "utility/BluefruitLE_SPI_Stream.h" -BluefruitLE_SPI_Stream stream(BLE_SPI_CS, BLE_SPI_IRQ, BLE_SPI_RST); -#endif - - -/* - * RedBearLab BLE Nano (with default switch settings) - * - * Blocked on this issue: https://github.com/RedBearLab/nRF51822-Arduino/issues/46 - * Works with modifications. See comments at top of the test script referenced below. - * When the RBL nRF51822-Arduino library issue is resolved, this should work witout - * any modifications. - * - * Test script: https://gist.github.com/soundanalogous/d39bb3eb36333a0906df - * - * Note: If you have changed the solder jumpers on the Nano you may encounter issues since - * the pins are currently mapped in Firmata only for the default (factory) jumper settings. - */ -// #ifdef BLE_NANO -// #include "utility/BLEStream.h" -// BLEStream stream; -// #endif - - -/* - * RedBearLab Blend and Blend Micro - * - * StandardFirmataBLE requires too much Flash and RAM to run on the ATmega32u4-based Blend - * and Blend Micro boards. It may work with ConfigurableFirmata selecting only analog and/or - * digital I/O. - */ -// #if defined(BLEND_MICRO) || defined(BLEND) -// #include <SPI.h> -// #include "utility/BLEStream.h" - -// #define BLE_REQ 6 -// #define BLE_RDY 7 -// #define BLE_RST 4 - -// BLEStream stream(BLE_REQ, BLE_RDY, BLE_RST); -// #endif - - -#if defined(BLE_REQ) && defined(BLE_RDY) && defined(BLE_RST) -#define IS_IGNORE_BLE_PINS(p) ((p) == BLE_REQ || (p) == BLE_RDY || (p) == BLE_RST) -#elif defined(BLE_SPI_CS) && defined(BLE_SPI_IRQ) && defined(BLE_SPI_RST) -#define IS_IGNORE_BLE_PINS(p) ((p) == BLE_SPI_CS || (p) == BLE_SPI_IRQ || (p) == BLE_SPI_RST) -#endif |