arduino stuffs
Diffstat (limited to 'libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h')
| -rw-r--r-- | libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h | 94 |
1 files changed, 94 insertions, 0 deletions
diff --git a/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h b/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h new file mode 100644 index 0000000..baf3465 --- /dev/null +++ b/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h @@ -0,0 +1,94 @@ +/*============================================================================== + * NETWORK CONFIGURATION + * + * You must configure your particular hardware. Follow the steps below. + * + * By default, StandardFirmataEthernet is configured as a TCP client. + * To configure as a TCP server, see STEP 2 + *============================================================================*/ + +// STEP 1 [REQUIRED] +// Uncomment / comment the appropriate set of includes for your hardware (OPTION A or B) +// Option A is enabled by default. + +/* + * OPTION A: Configure for Arduino Ethernet board or Arduino Ethernet shield (or clone) + * + * To configure StandardFirmataEthernet to use the original WIZ5100-based + * ethernet shield or Arduino Ethernet uncomment the WIZ5100_ETHERNET define below + */ +#define WIZ5100_ETHERNET + +#ifdef WIZ5100_ETHERNET +#include <SPI.h> +#include <Ethernet.h> +EthernetClient client; +#endif + +/* + * OPTION B: Configure for Arduin Yun + * + * The Ethernet port on the Arduino Yun board can be used with Firmata in this configuration. + * + * To execute StandardFirmataEthernet on Yun uncomment the YUN_ETHERNET define below and make + * sure the WIZ5100_ETHERNET define (above) is commented out. + * + * On Yun there's no need to configure local_ip and mac address as this is automatically + * configured on the linux-side of Yun. + * + * Note that it may take several seconds to establish a connection with the Yun. + */ +//#define YUN_ETHERNET + +#ifdef YUN_ETHERNET +#include <Bridge.h> +#include <YunClient.h> +YunClient client; +#endif + +// STEP 2 [REQUIRED for all boards and shields] +// TCP Client configuration: +// To configure your board as a TCP client, set the IP address of the server you want to connect to. +// TCP Server configuration: +// To configure your board as a TCP server, comment out the following line and also ensure that +// remote_host is also commented out. +#define remote_ip IPAddress(10, 0, 0, 3) +// *** REMOTE HOST IS NOT YET WORKING *** +// replace with hostname of server you want to connect to, comment out if using 'remote_ip' +// #define remote_host "server.local" + +// STEP 3 [REQUIRED] +// Replace with the port that your client or server is listening on. +#define network_port 3030 + +// STEP 4 [REQUIRED unless using DHCP] +// Replace with your board or ethernet shield's IP address +// Comment out if you want to use DHCP +#define local_ip IPAddress(10, 0, 0, 15) + +// STEP 5 [REQUIRED] +// replace with ethernet shield mac. Must be unique for your network +const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5}; + +/*============================================================================== + * CONFIGURATION ERROR CHECK (don't change anything here) + *============================================================================*/ + +#if !defined WIZ5100_ETHERNET && !defined YUN_ETHERNET +#error "you must define either WIZ5100_ETHERNET or YUN_ETHERNET in ethernetConfig.h" +#endif + +#if defined remote_ip && defined remote_host +#error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h" +#endif + +/*============================================================================== + * PIN IGNORE MACROS (don't change anything here) + *============================================================================*/ + +#if defined(WIZ5100_ETHERNET) + +// ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield) +#define IS_IGNORE_PIN(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10) + +#endif |