arduino stuffs
Diffstat (limited to 'libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h')
| -rw-r--r-- | libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h | 94 |
1 files changed, 0 insertions, 94 deletions
diff --git a/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h b/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h deleted file mode 100644 index baf3465..0000000 --- a/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h +++ /dev/null @@ -1,94 +0,0 @@ -/*============================================================================== - * NETWORK CONFIGURATION - * - * You must configure your particular hardware. Follow the steps below. - * - * By default, StandardFirmataEthernet is configured as a TCP client. - * To configure as a TCP server, see STEP 2 - *============================================================================*/ - -// STEP 1 [REQUIRED] -// Uncomment / comment the appropriate set of includes for your hardware (OPTION A or B) -// Option A is enabled by default. - -/* - * OPTION A: Configure for Arduino Ethernet board or Arduino Ethernet shield (or clone) - * - * To configure StandardFirmataEthernet to use the original WIZ5100-based - * ethernet shield or Arduino Ethernet uncomment the WIZ5100_ETHERNET define below - */ -#define WIZ5100_ETHERNET - -#ifdef WIZ5100_ETHERNET -#include <SPI.h> -#include <Ethernet.h> -EthernetClient client; -#endif - -/* - * OPTION B: Configure for Arduin Yun - * - * The Ethernet port on the Arduino Yun board can be used with Firmata in this configuration. - * - * To execute StandardFirmataEthernet on Yun uncomment the YUN_ETHERNET define below and make - * sure the WIZ5100_ETHERNET define (above) is commented out. - * - * On Yun there's no need to configure local_ip and mac address as this is automatically - * configured on the linux-side of Yun. - * - * Note that it may take several seconds to establish a connection with the Yun. - */ -//#define YUN_ETHERNET - -#ifdef YUN_ETHERNET -#include <Bridge.h> -#include <YunClient.h> -YunClient client; -#endif - -// STEP 2 [REQUIRED for all boards and shields] -// TCP Client configuration: -// To configure your board as a TCP client, set the IP address of the server you want to connect to. -// TCP Server configuration: -// To configure your board as a TCP server, comment out the following line and also ensure that -// remote_host is also commented out. -#define remote_ip IPAddress(10, 0, 0, 3) -// *** REMOTE HOST IS NOT YET WORKING *** -// replace with hostname of server you want to connect to, comment out if using 'remote_ip' -// #define remote_host "server.local" - -// STEP 3 [REQUIRED] -// Replace with the port that your client or server is listening on. -#define network_port 3030 - -// STEP 4 [REQUIRED unless using DHCP] -// Replace with your board or ethernet shield's IP address -// Comment out if you want to use DHCP -#define local_ip IPAddress(10, 0, 0, 15) - -// STEP 5 [REQUIRED] -// replace with ethernet shield mac. Must be unique for your network -const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5}; - -/*============================================================================== - * CONFIGURATION ERROR CHECK (don't change anything here) - *============================================================================*/ - -#if !defined WIZ5100_ETHERNET && !defined YUN_ETHERNET -#error "you must define either WIZ5100_ETHERNET or YUN_ETHERNET in ethernetConfig.h" -#endif - -#if defined remote_ip && defined remote_host -#error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h" -#endif - -/*============================================================================== - * PIN IGNORE MACROS (don't change anything here) - *============================================================================*/ - -#if defined(WIZ5100_ETHERNET) - -// ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield) -#define IS_IGNORE_PIN(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10) - -#endif |